1/11 may 2001 STP6NC90Z - STP6NC90Zfp stb6nc90z-1 n-channel 900v - 1.55 w - 5.4a to-220/to-220fp /i pak zener-protected powermesh ? iii mosfet n typical r ds (on) = 1.55 w n extremely high dv/dt and capability gate to - source zener diodes n 100% avalanche tested n very low gate input resistance n gate charge minimized description the third generation of mesh overlay ? power mosfets for very high voltage exhibits unsurpassed on-resistance per unit area while integrating back-to- back zener diodes between gate and source. such ar- rangement gives extra esd capability with higher rug- gedness performance as requested by a large variety of single-switch applications. applications n single-ended smps in monitors, computer and industrial application n welding equipment absolute maximum ratings ( ? )pulse width limited by safe operating area type v dss r ds(on) i d STP6NC90Z/fp 900v < 1.9 w 5.4 a stb6nc90z-1 900v < 1.9 w 5.4 a symbol parameter value unit stp(b)6nc90z(-1) STP6NC90Zfp v ds drain-source voltage (v gs =0) 900 v v dgr drain-gate voltage (r gs =20k w ) 900 v v gs gate- source voltage 25 v i d drain current (continuos) at t c =25 c 5.4 5.4(*) a i d drain current (continuos) at t c = 100 c 4.9 4.9(*) a i dm (1) drain current (pulsed) 21 21 a p tot total dissipation at t c =25 c 135 40 w derating factor 1.08 0.32 w/ c i gs gate-source current 50 ma v esd(g-s) gate source esd(hbm-c=100pf, r=15k w) 3kv dv/dt peak diode recovery voltage slope 3 v/ns v iso insulation withstand voltage (dc) -- 2000 v t stg storage temperature 65 to 150 c t j max. operating junction temperature 150 c (1)i sd 5.4a, di/dt 100a/ m s, v dd v (br)dss ,t j t jmax (2) . limited only by maximum temperature allowed to-220 1 2 3 to-220fp 1 2 3 i pak (tabless to-220)
STP6NC90Z/fp/stb6nc90z-1 2/11 thermal data avalanche characteristics electrical characteristics (tcase = 25 c unless otherwise specified) off on (1) dynamic to-220 / i pak to-220fp rthj-case thermal resistance junction-case max 0.93 3.13 c/w rthj-amb thermal resistance junction-ambient max 30 c/w t l maximum lead temperature for soldering purpose 300 c symbol parameter max value unit i ar avalanche current, repetitive or not-repetitive (pulse width limited by t j max) 5.4 a e as single pulse avalanche energy (starting t j =25 c, i d =i ar ,v dd =50v) 356 mj symbol parameter test conditions min. typ. max. unit v (br)dss drain-source breakdown voltage i d = 250 m a, v gs = 0 900 v d bv dss / d t j breakdown voltage temp. coefficient i d =1ma,v gs =0 1 v/ c i dss zero gate voltage drain current (v gs =0) v ds = max rating 1 m a v ds = max rating, t c = 125 c 50 m a i gss gate-body leakage current (v ds =0) v gs = 20v 10 m a symbol parameter test conditions min. typ. max. unit v gs(th) gate threshold voltage v ds =v gs ,i d = 250 m a 345v r ds(on) static drain-source on resistance v gs = 10v, i d = 3 a 1.55 1.9 w symbol parameter test conditions min. typ. max. unit g fs (1) forward transconductance v ds >i d(on) xr ds(on)max, i d =3a 5.7 s c iss input capacitance v ds = 25v, f = 1 mhz, v gs = 0 2290 pf c oss output capacitance 150 pf c rss reverse transfer capacitance 15 pf
3/11 STP6NC90Z/fp/stb6nc90z-1 electrical characteristics (continued) switching on switching off source drain diode gate-source zener diode note: 1. pulsed: pulse duration = 300 m s, duty cycle 1.5 %. 2. pulse width limited by safe operating area. 3. d v bv = a t(25 -t) bv gso (25 ) protection features of gate-to-source zener diodes the built-in back-to-back zener diodes have specifically been designed to enhance not only the device's esd capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to souce. in this respect the 25v zener voltage is appropiate to achieve an efficient and cost-effective intervention to protect the device's integrity. these integrated zener diodes thus avoid the usage of external components. symbol parameter test conditions min. typ. max. unit t d(on) turn-on delay time v dd = 450 v, i d =3a r g = 4.7 w v gs = 10v (see test circuit, figure 3) 24 ns t r rise time 8 ns q g total gate charge v dd = 720v, i d = 6a, v gs = 10v 42 58.8 nc q gs gate-source charge 13 nc q gd gate-drain charge 15 nc symbol parameter test condit ions min. typ. max. unit t r(voff) off-voltage rise time v dd = 720v, i d =6a, r g =4.7 w, v gs = 10v (see test circuit, figure 5) 10 ns t f fall time 11 ns t c cross-over time 14 ns symbol parameter test conditions min. typ. max. unit i sd source-drain current 5.4 a i sdm (2) source-drain current (pulsed) 21.6 a v sd (1) forward on voltage i sd = 6 a, v gs =0 1.6 v t rr reverse recovery time i sd = 6 a, di/dt = 100a/ m s, v dd =40v,t j = 150 c (see test circuit, figure 5) 680 ns q rr reverse recovery charge 7.14 m c i rrm reverse recovery current 21 a symbol parameter test conditions min. typ. max. unit bv gso gate-source breakdown voltage igs= 1ma (open drain) 25 v a t voltage thermal coefficient t=25 c note(3) 1.3 10 -4 / c rz dynamic resistance i d = 50 ma, v gs =0 90 w
STP6NC90Z/fp/stb6nc90z-1 4/11 safe operating area for to-220 / i pak safe operating area for to-220fp output characteristics thermal impedance for to-220 / i pak thermal impedance for to-220fp transfer characteristics
5/11 STP6NC90Z/fp/stb6nc90z-1 normalized gate threshold voltage vs temp. normalized on resistance vs temperature gate charge vs gate-source voltage capacitance variations static drain-source on resistance transconductance
STP6NC90Z/fp/stb6nc90z-1 6/11 source-drain diode forward characteristics
7/11 STP6NC90Z/fp/stb6nc90z-1 fig. 5: test circuit for inductive load switching and diode recovery times fig. 4: gate charge test circuit fig. 2: unclamped inductive waveform fig. 1: unclamped inductive load test circuit fig. 3: switching times test circuits for resistive load
STP6NC90Z/fp/stb6nc90z-1 8/11 dim. mm inch min. typ. max. min. typ. max. a 4.40 4.60 0.173 0.181 c 1.23 1.32 0.048 0.051 d 2.40 2.72 0.094 0.107 d1 1.27 0.050 e 0.49 0.70 0.019 0.027 f 0.61 0.88 0.024 0.034 f1 1.14 1.70 0.044 0.067 f2 1.14 1.70 0.044 0.067 g 4.95 5.15 0.194 0.203 g1 2.4 2.7 0.094 0.106 h2 10.0 10.40 0.393 0.409 l2 16.4 0.645 l4 13.0 14.0 0.511 0.551 l5 2.65 2.95 0.104 0.116 l6 15.25 15.75 0.600 0.620 l7 6.2 6.6 0.244 0.260 l9 3.5 3.93 0.137 0.154 dia. 3.75 3.85 0.147 0.151 l6 a c d e d1 f g l7 l2 dia. f1 l5 l4 h2 l9 f2 g1 to-220 mechanical data p011c
|
